MEC2405 Machine Dynamics
|Semester 1, 2012 External Toowoomba|
|Faculty or Section :||Faculty of Engineering & Surveying|
|School or Department :||Mechanical and Mechatronic Engineering|
|Version produced :||30 December 2013|
Examiner: Peter Penfold
Moderator: Chris Snook
A knowledge of the basic laws of dynamics, vibration and mechanisms are fundamental for the solution of many engineering problems. This course develops, at an appropriate level, theoretical and practical methods used in the design of machine elements.
The course objectives define the student learning outcomes for a course. On completion of this course, students should be able to:
- analyse the kinematics of planar motion of a particle and rigid body;
- use the free body diagram method to solve simple problems involving the forces particles and rigid bodies and their resulting planar motion;
- calculate the velocity and acceleration of any point within a simple 2D mechanism;
- apply the principles of work-energy and impulse-momentum to the analysis of simple bodies in 2D motion;
- calculate the dynamic forces resulting from rotating out-of-balance masses and determine the corrective masses to balance that system;
- determine the dynamic behaviour of a range of common engineering devices;
- analyse the vibrational response of simple single-degree-of-freedom systems to determine damped and undamped frequencies, amplitude and the forces transmitted to the system's support.
|1.||Kinematics, linear and rotational motion||10.00|
|2.||Kinetics, force and motion||10.00|
|3.||Work and energy, flywheels||10.00|
|4.||Impulse and momentum||10.00|
|5.||Kinematics of mechanisms||15.00|
|6.||Friction, brakes, clutches, belt drives, power screws||10.00|
|7.||Balancing of Rotating Masses||15.00|
|8.||Gears and geared systems||10.00|
Text and materials required to be purchased or accessed
ALL textbooks and materials available to be purchased can be sourced from USQ's Online Bookshop (unless otherwise stated). (https://bookshop.usq.edu.au/bookweb/subject.cgi?year=2012&sem=01&subject1=MEC2405)
Please contact us for alternative purchase options from USQ Bookshop. (https://bookshop.usq.edu.au/contact/)
Ryder, GH & Bennett, MD 1990, Mechanics of machines, 2nd edn, MacMillan, London.
Student workload requirements
|Description||Marks out of||Wtg (%)||Due Date||Notes|
|ASSIGNMENT||400||40||11 May 2012|
|2 HOUR OPEN EXAMINATION||600||60||End S1||(see note 1)|
- Student Administration will advise students of the dates of their examinations during the semester.
Important assessment information
There are no attendance requirements for this course. However, it is the students' responsibility to study all material provided to them or required to be accessed by them to maximise their chance of meeting the objectives of the course and to be informed of course-related activities and administration.
Requirements for students to complete each assessment item satisfactorily:
To satisfactorily complete an assessment item a student must achieve at least 50% of the marks or a grade of at least C-. Students do not have to satisfactorily complete each assessment item to be awarded a passing grade in this course. Refer to Statement 4 below for the requirements to receive a passing grade in this course.
Penalties for late submission of required work:
If students submit assignments after the due date without (prior) approval of the examiner then a penalty of 5% of the total marks gained by the student for the assignment may apply for each working day late up to ten working days at which time a mark of zero may be recorded.. No assignments will be accepted after model answers have been posted.
Requirements for student to be awarded a passing grade in the course:
To be assured of receiving a passing grade in a course a student must obtain at least 50% of the total weighted marks for the course.
Method used to combine assessment results to attain final grade:
The final grades for students will be assigned on the basis of the weighted aggregate of the marks (or grades) obtained for each of the summative assessment item in the course.
In an Open Examination, candidates may have access to any material during the examination except the following: electronic communication devices, bulky materials, devices requiring mains power and material likely to disturb other students.
Examination period when Deferred/Supplementary examinations will be held:
Any Deferred or Supplementary examinations for this course will be held during the examination period at the end of the semester of the next offering of this course.
University Student Policies:
Students should read the USQ policies: Definitions, Assessment and Student Academic Misconduct to avoid actions which might contravene University policies and practices. These policies can be found at http://policy.usq.edu.au.
The due date for an assignment is the date by which a student must despatch the assignment to the USQ. The onus is on the student to provide proof of the despatch date, if requested by the Examiner.
Students must retain a copy of each item submitted for assessment. This must be despatched to USQ within 24 hours if required by the Examiner.
In accordance with University Policy, the Examiner may grant an extension of the due date of an assignment in extenuating circumstances.
If electronic submission of assessments is specified for the course, students will be notified of this in the course Introductory Book and on the USQ Study Desk. All required electronic submission must be made through the Assignment Drop Box located on the USQ Study Desk for the course, unless directed otherwise by the examiner of the course. The due date for an electronically submitted assessment is the date by which a student must electronically submit the assignment. The assignment files must be submitted by 11.55pm on the due date using USQ time (as displayed on the clock on the course home page; that is, Australian Eastern Standard Time).
If the method of assessment submission is by written, typed or printed paper-based media students should (i) submit to the Faculty Office for students enrolled in the course in the on-campus mode, or (ii) mail to the USQ for students enrolled in the course in the external mode. The due date for the assessment is the date by which a student must (i) submit the assessment for students enrolled in the on-campus mode, or (ii) mail the assessment for students enrolled in the external mode.
The Faculty will NOT normally accept submission of assessments by facsimile or email.
Students who do not have regular access to postal services for the submission of paper-based assessments, or regular access to Internet services for electronic submission, or are otherwise disadvantaged by these regulations may be given special consideration. They should contact the examiner of the course to negotiate such special arrangements prior to the submission date.
Students who have undertaken all of the required assessments in a course but who have failed to meet some of the specified objectives of a course within the normally prescribed time may be awarded the temporary grade: IM (Incomplete - Make up). An IM grade will only be awarded when, in the opinion of the examiner, a student will be able to achieve the remaining objectives of the course after a period of non-directed personal study.
Students who, for medical, family/personal, or employment-related reasons, are unable to complete an assignment or to sit for an examination at the scheduled time may apply to defer an assessment in a course. Such a request must be accompanied by appropriate supporting documentation. One of the following temporary grades may be awarded IDS (Incomplete - Deferred Examination; IDM (Incomplete Deferred Make-up); IDB (Incomplete - Both Deferred Examination and Deferred Make-up).
Harvard (AGPS) is the referencing system required in this course. Students should use Harvard (AGPS) style in their assignments to format details of the information sources they have cited in their work. The Harvard (AGPS) style to be used is defined by the USQ Library's referencing guide. http://www.usq.edu.au/library/referencing