ELE2704 Electricity Supply Systems
|Semester 2, 2019 Online|
|Short Description:||Electricity Supply Systems|
|Faculty or Section :||Faculty of Health, Engineering and Sciences|
|School or Department :||School of Mechanical and Electrical Engineering|
|Student contribution band :||Band 2|
|ASCED code :||031301 - Electrical Engineering|
|Grading basis :||Graded|
Examiner: Gordon Hampson
Pre-requisite: ELE1801 or Students must be enrolled in one of the following Programs: MEPR or GCEN or METC
Recommended prior or concurrent study: ELE3803 or ELE2702.
This course introduces the principles and practical aspects of generation, transmission distribution and control of electrical energy. On successful completion of this course, the student should be able to discuss the technical, environmental and economic considerations of planning and operating different types of electrical plant (generators, transformers, circuit breakers, cables, insulators and transmission lines), as well as principles of substation layout, control, instrumentation and protection. The student should also be aware of the theoretical principles of system stability, load flow, and fault analysis of power systems using computing software tools.
The course objectives define the student learning outcomes for a course. On completion of this course, students should be able to:
- justify the typical structure of modern electricity supply systems on the basis of economics, reliability, safety and technical constraints;
- compare underground cables against overhead lines on the basis of environmental impact, cost, technical performance and supply reliability;
- analyse three-phase electrical networks under abnormal conditions;
- determine, by qualitative analysis, the performance requirements of electricity supply system practical hardware;
- analyse the impact of transformer tap-change on the voltage profile of radial feeders;
- compare the relative strengths and weaknesses of typical protection schemes.
|1.||Power systems: environment and planning; economics||10.00|
|2.||Generation, transmission and distribution systems||10.00|
|3.||Lines, distributors and cables||10.00|
|4.||Surges; insulation co-ordination||7.50|
|5.||Loads, scheduling and voltage control||7.50|
|6.||High voltage testing, commissioning||5.00|
|7.||Substations: layout; reliability; safety||10.00|
|8.||High voltage switchgear||10.00|
|9.||Protection schemes; protection relays||10.00|
|10.||Fault calculations and symmetrical components||15.00|
|11.||Supervisory control and communications co-ordination.||5.00|
Text and materials required to be purchased or accessed
ALL textbooks and materials available to be purchased can be sourced from USQ's Online Bookshop (unless otherwise stated). (https://omnia.usq.edu.au/textbooks/?year=2019&sem=02&subject1=ELE2704)
Please contact us for alternative purchase options from USQ Bookshop. (https://omnia.usq.edu.au/info/contact/)
(available from the USQ Bookshop.)
(USQ Library Call No. 621.31 Nas.)
(USQ Library Call No. 621.31 Nas.)
(USQ Library Call No: 621.319 Pab.)
(USQ Library Call No: 621.3191 Wee.)
(USQ Library Call No: 621.31913 Whi.)
Student workload expectations
|Description||Marks out of||Wtg (%)||Due Date||Objectives Assessed||Notes|
|Assignment 1||150||15||07 Aug 2019||2,4|
|Assignment 2||150||15||04 Sep 2019||2,3|
|Assignment 3||100||10||08 Oct 2019||3,4|
|Exam||600||60||End S2||1,2,5,6||(see note 1)|
- This will be a closed exam. The total working time for the examination is 2 hours. The examination date will be available via UConnect when the official examination timetable has been released.
Important assessment information
It is the students' responsibility to attend and participate appropriately in all activities (such as lectures, tutorials, laboratories and practical work) scheduled for them, and to study all material provided to them or required to be accessed by them to maximise their chance of meeting the objectives of the course and to be informed of course-related activities and administration.
Requirements for students to complete each assessment item satisfactorily:
To satisfactorily complete an assessment item a student must achieve at least 50% of the marks or a grade of at least C-. Students do not have to satisfactorily complete each assessment item to be awarded a passing grade in this course. Refer to Statement 4 below for the requirements to receive a passing grade in this course.
Penalties for late submission of required work:
Students should refer to the Assessment Procedure http://policy.usq.edu.au/documents.php?id=14749PL (point 4.2.4)
Requirements for student to be awarded a passing grade in the course:
To be assured of receiving a passing grade a student must obtain at least 50% of the total weighted marks available for the course (i.e. the Primary Hurdle), and have satisfied the Secondary Hurdle (Supervised), i.e. the end of semester examination by achieving at least 40% of the marks available for that assessment item.
Supplementary assessment may be offered where a student has undertaken all of the required summative assessment items and has passed the Primary Hurdle but failed to satisfy the Secondary Hurdle (Supervised), or has satisfied the Secondary Hurdle (Supervised) but failed to achieve a passing Final Grade by 5% or less of the total weighted Marks.
To be awarded a passing grade for a supplementary assessment item (if applicable), a student must achieve at least 50% of the available marks for the supplementary assessment item as per the Assessment Procedure http://policy.usq.edu.au/documents/14749PL (point 4.4.2).
Method used to combine assessment results to attain final grade:
The final grades for students will be assigned on the basis of the weighted aggregate of the marks (or grades) obtained for each of the summative assessment items in the course.
In a Closed Examination, candidates are allowed to bring only writing and drawing instruments into the examination.
Examination period when Deferred/Supplementary examinations will be held:
Any Deferred or Supplementary examinations for this course will be held during the next examination period.
University Student Policies:
Students should read the USQ policies: Definitions, Assessment and Student Academic Misconduct to avoid actions which might contravene University policies and practices. These policies can be found at http://policy.usq.edu.au.
Students must familiarise themselves with the USQ Assessment Procedures (http://policy.usq.edu.au/documents.php?id=14749PL).
IEEE is the referencing system required in this course. Students should use IEEE style in their assignments to format details of the information sources they have cited in their work. For further information on this referencing style, refer to the below website:
Students will require access to e-mail and internet access to UConnect for this course.
Students will require access to a printer to print modest quantities of material that may be provided via the StudyDesk.
Students will require access to a document scanner to compile three PDFs, one for each of Assignments 1, 2 and 3